3500/15 AC and DC Power Supplies
3500/15 AC and DC Power Supplies
AC Power Supply Module
Bently Nevada
Bently Nevada 3500 System
Estimated Shipping Size
Dimensions: 2.0″ x 10.0″ x 5.0″
(5.1 cm x 25.4 cm x 12.7 cm)
Weight: 0 lbs 10.1 oz (0.3kg )
Ships from Webster NY, USA
Description
The 3500/15 AC and DC Power Supplies are half-height modules and must be installed in designated slots on the left side of the rack. The 3500 rack can contain one or two power supplies with any combinations of AC and DC. Either supply can power a full rack. When two power supplies are installed in a rack, the one in the lower slot acts as the primary supply, and the other in the upper slot acts as the backup supply. If installed, the second supply is the backup for the primary one. Removing or inserting either power supply module does not disrupt operation of the rack as long as a second power supply is installed. The 3500/15 AC and DC Power Supplies accepts a wide range of input voltages and converts them to voltages acceptable for use by other 3500 modules. The following power supplies are available with the 3500 Series Machinery Protection System: l Universal AC Power l High Voltage DC Power Supply l Low Voltage DC Power Supply
3500/05 System Instrumentation Framework
3500/15 Power Module
3500/22M Rack Interface Module with TDI
3500/25 Keyphasor Module
3500/40 M Proximitor Monitor Module
3500/42 MProxmitor/Displacement/Velocity Acceleration Monitor Module
3500/45 Position Monitor Module
3500/32 4-Channel Relay Module
3500/33 16 Channel Relay Module
3500/34 TMR Relay Module
3500/50 Speed Module
3500/53 Overspeed Detection Module
3500/60 and 350061 Temperature Monitor Modules
3500/62 Process Variable Monitor Module
3500/64M Dynamic Pressure Monitor
3500/651 6-Channel Temperature Module
3500/70M Reciprocating Compressor Shock/Velocity Monitor
3500/72M Piston Rod Position Monitor
3500/77M Cylinder Pressure Monitor
3500/63 Gas Monitor
3500/92 Communication Gateway
3500/93 LCD Display Unit
3500/94 VGA Display Unit
3500/95 System Integrated PC Display Device
Relay Module 3500/33
Vibration and displacement monitor 3500/42
I/O Module Signal Common Terminal
A 2-pin connector for connecting Signal Common to a single point Instrument Ground for the rack is now present in both versions of the TDI I/O Module. To isolate Signal Common from chassis (safety) ground after doing this, slide the selector switch on the Power Input Module’s (PIM) side in the direction of the “HP” arrow.
Data Collection
Keyphasor Inputs
- Supports the four Keyphasor signals of the 3500 system.
- The amount of dynamic channels that are active determines the speed range support.
- Supports speed inputs with multiple occurrences per rotation up to 20 kHz.
Startup/Coastdown Data
- Data collected at predetermined intervals of speed and time; separately programmed increasing and lowering speed intervals.
- Collection of transitory data is started after a machine’s speed is detected inside one of two programmable windows.
- The module’s memory capacity is the only restriction on the amount of transitory events that can be gathered.
- Data collected at predetermined intervals of speed and time; separately programmed increasing and lowering speed intervals.
- Collection of transitory data is started after a machine’s speed is detected inside one of two programmable windows.
- The module’s memory capacity is the only restriction on the amount of transitory events that can be gathered.
Alarm Data Collection
- 2.5 minutes of waveform data collected at 10-second intervals before the alarm and 1 minute of waveform data collected at 10-second intervals after the alarm.
- Pre- and post-alarm data.
- Static values collected at one second intervals for 10 minutes before the event and 1 minute after the event.
- Static values collected at 100 ms intervals for 20 seconds before the event and 10 seconds after the event.
Static Values Data
- The static values, including those determined by the monitors, will be gathered by TDI.
- For each point, l TDI offers four nX static values. For each of the values, amplitude and phase are returned.
3500/22M Communications
BN Host Protocol
3500 Configuration Software, 3500 Data Acquisition Software, and 3500 Display Software in BN Host Protocol Communication
BN TDI Protocol
System 1 Condition Monitoring and Diagnostic Software and the BN TDI Protocol
supports a large number of Bently Nevada parts, including 3500/45. Please do not hesitate to contact us if you require additional information or have a question.
FREQUENTLY ASKED QUESTIONS on 3500/22M
What is Bently Nevada 3500/22M?
3500/22M is a Transient Data Interface module developed by Bently Nevada.
What is the function of 3500/22M?
The component link 3500 monitoring system and compatible software.
Where is TDI located in the rack?
In a 3500 rack, the TDI is located in the slot next to the power supplies
